Are you looking to enhance the safety and convenience of your RV travels? Installing a ZEROXCLUB BW7 backup camera system can provide you with added peace of mind while on the road. In this guide, we will walk you through the steps to install the BW7 backup camera system on Furrion pre-wired vehicles.
Gather the Necessary Tools
Before you begin, make sure you have the necessary tools on hand. You will need a screwdriver, voltage tester, electrical tape, and a ladder. Having everything prepared will streamline the process.
What's in the Box?
Make sure you have all the necessary components: the camera, monitor, suction cup mount, rubber gasket, power cables, and any additional accessories included in the package.
Testing the System
Before you begin the installation process, connect the system to a temporary power source and test the system to see if it works. If you have problems, click here for troubleshooting tips.
Adjust the camera angle according to your usage habits. Click here to see a video of the adjustment
Remove the Pre-Wired Mounting Bracket
Most Furrion RVs come pre-wired for backup camera systems, making the installation process much easier. Locate the pre-wired mounting bracket on the back of your RV. Remove the 4 screws holding that original cover for the pre-wired system and remove it's gasket.
Mount the Camera
Once you have removed the pre-Wired mounting bracket, it's time to attach the BW7 camera. The connector on this camera plugs right into the prewired jack. Line up the new gasket and camera and put the 4 supplied screws back into the original holes and plug in to the same power connector. Make sure the camera is positioned securely and is angled correctly for optimal visibility. Turn your headlights/running lights on they connected successfully.
Please note that many RV manufacturers hook the RV running light to the preinstalled mount. So typically your tow vehicle's running lights must be on to energize the RV's running lights.
Click here to watch a compatible side view camera installation video
Mount the Monitor
Next, decide on the placement of the monitor inside your vehicle. It should be easily visible to the driver without obstructing their view of the road. Use the provided mounting brackets to secure the monitor in place. Power the monitor with the included power adapter.
Adjusting the Settings
Take the time to adjust the camera settings to suit your preferences. You may need to change the angle or brightness to optimize the view based on your driving conditions.
If you would like to know more about the BW7 system, please click here to view the FAQ.
Final Checks
Before hitting the road, double-check all the connections and mounting points to ensure everything is secure. It's essential to have a reliable backup camera system that functions properly at all times.
If your vehicle is not pre-wired, you will need to drill or mount with magnets （not included）and run 12 volt power from a nearby source.
This system supports up to 4 cameras, and you can add a separate side-view one. You can click here to see more.
Mount the side view camera
IMPORTANT: Before any installation and wiring operation, remove the key from the ignition and isolate the 12V / 24V power source.
Always seek professional assistance if you are unsure about the installation and wiring operation.
1. Determine the mounting location on your vehicle. Ensure that there is no obstacle blocking the camera view.
2. Use the gasket as a template to mark a basic outline on the chosen location with a pencil. Drill holes. Fix the gasket and bracket with three screws. Then route the female connector of the camera power cable through the center hole or leave it outsdie the vehicle.
3. Mount the antenna onto the camera securely.
4. Align the notched portion and secure the camera to the bracket. Then attach the camera to the bracket with two screws.
5. Connect the female connector of the power cable to the male connector on the back of the camera. Connect the bare ends of the camera power cable to the nearest 12V / 24Vpower supply.
Click here to view the side view camera installation video.
By following these steps, you can successfully install the ZEOXCLUB BW7 backup camera system on your Furrion pre-wired vehicle. Enhance your safety and convenience while traveling and enjoy the added peace of mind that comes with having a reliable backup camera system in place. If you encounter any difficulties during the installation process, refer to the BW7's manual for troubleshooting tips.